Enfield-Rifles.com Homepage
Forum Home Forum Home > Enfields > After Market Enfields
  New Posts New Posts RSS Feed - Santa Fe Supreme No4 scope mount part 2
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Santa Fe Supreme No4 scope mount part 2

 Post Reply Post Reply
Author
Message
Goosic View Drop Down
Senior Member
Senior Member
Avatar

Joined: September 12 2017
Location: Phoenix Arizona
Status: Offline
Points: 781
Post Options Post Options   Thanks (0) Thanks(0)   Quote Goosic Quote  Post ReplyReply Direct Link To This Post Topic: Santa Fe Supreme No4 scope mount part 2
    Posted: May 12 2018 at 9:24pm
Oldhand entrusted me with his rifle today. The mount I made for his rifle and then sent to him via USPS,arrived with a screw hole still off a tad and the bottom part protruding over the ejector screw. I met him today halfway between Phoenix and Tucson to take his rifle home with me so I could make this all come to fruition. It did. I also took it upon myself to replace the No1 MkIII cocking piece with a new, unissued No4 cocking piece and matching striker. Smoothed out the trigger and sear assembly,cleaned and polished the bolt assembly,blueing where needed. Cleaned all the old blueing off, repolished the entire barrel and receiver and then re blued it. Recrowned the barrel along the way. Did not intensionally mean to do all that,it just happened.
My Faux Parker Hale Custom No4 is on top, Oldhands​ Santa Fe Supreme No4 is on the bottom...

Back to Top
Sponsored Links


Back to Top
Canuck View Drop Down
Special Member
Special Member
Avatar
Donating Member

Joined: January 17 2012
Location: Agassiz BC
Status: Offline
Points: 2199
Post Options Post Options   Thanks (0) Thanks(0)   Quote Canuck Quote  Post ReplyReply Direct Link To This Post Posted: May 13 2018 at 7:55am
Very nice job! Gorgeous rifles there!
Castles made of sand slip into the sea.....eventually
Back to Top
Honkytonk View Drop Down
Senior Member
Senior Member
Avatar

Joined: December 30 2017
Location: Brandon Mb
Status: Offline
Points: 866
Post Options Post Options   Thanks (0) Thanks(0)   Quote Honkytonk Quote  Post ReplyReply Direct Link To This Post Posted: May 13 2018 at 8:07am
Both very nice examples! I'm a sucker for the front site hoop guard! You know, the one you always lost after pushing bush!
Back to Top
Goosic View Drop Down
Senior Member
Senior Member
Avatar

Joined: September 12 2017
Location: Phoenix Arizona
Status: Offline
Points: 781
Post Options Post Options   Thanks (0) Thanks(0)   Quote Goosic Quote  Post ReplyReply Direct Link To This Post Posted: May 13 2018 at 8:13am
Oldhands rifle does not have that option. There's no groove in the ramp to accommodate a hood...
Back to Top
Shamu View Drop Down
Admin Group
Admin Group
Avatar
Logo Designer / Donating Member

Joined: April 25 2007
Location: MD, USA.
Status: Offline
Points: 8733
Post Options Post Options   Thanks (0) Thanks(0)   Quote Shamu Quote  Post ReplyReply Direct Link To This Post Posted: May 13 2018 at 8:57am
Wow! That crown is DEEP!

Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)
Back to Top
Goosic View Drop Down
Senior Member
Senior Member
Avatar

Joined: September 12 2017
Location: Phoenix Arizona
Status: Offline
Points: 781
Post Options Post Options   Thanks (0) Thanks(0)   Quote Goosic Quote  Post ReplyReply Direct Link To This Post Posted: May 13 2018 at 12:02pm
It does in fact look deep. It's the angle of the picture taken. I went just far enough to remove the wore out end of the barrel without trimming the end of the barrel itself. The angle and depth of the crown acts as a tiny muzzle brake, directing the spent gasses outwards in a consistent rate to keep the recoil in a horizontal pattern without the barrel lift...
Back to Top
Oldhand View Drop Down
Groupie
Groupie
Avatar

Joined: February 19 2018
Location: Tucson, Az
Status: Offline
Points: 76
Post Options Post Options   Thanks (0) Thanks(0)   Quote Oldhand Quote  Post ReplyReply Direct Link To This Post Posted: May 13 2018 at 3:12pm
The work Goosic did was far and above what I expected. I went in expecting just a scope mount, he completely tuned and went thru the entire rifle. I highly recommend his work to all that require a mount our just need their rifle tuned.
Retired USAF, NRA life member
Back to Top
Honkytonk View Drop Down
Senior Member
Senior Member
Avatar

Joined: December 30 2017
Location: Brandon Mb
Status: Offline
Points: 866
Post Options Post Options   Thanks (0) Thanks(0)   Quote Honkytonk Quote  Post ReplyReply Direct Link To This Post Posted: May 13 2018 at 3:41pm
Yup. Gases gotta come out equal or no accuracy! 20 years ago I had know idea what crowning meant. My buddies still don't. Nice job!
Back to Top
Ranch Dog View Drop Down
Groupie
Groupie
Avatar

Joined: February 21 2018
Location: Texas
Status: Offline
Points: 36
Post Options Post Options   Thanks (0) Thanks(0)   Quote Ranch Dog Quote  Post ReplyReply Direct Link To This Post Posted: May 20 2018 at 7:58am
Very nice work!
Back to Top
Goosic View Drop Down
Senior Member
Senior Member
Avatar

Joined: September 12 2017
Location: Phoenix Arizona
Status: Offline
Points: 781
Post Options Post Options   Thanks (0) Thanks(0)   Quote Goosic Quote  Post ReplyReply Direct Link To This Post Posted: May 20 2018 at 8:02am
Thank you...
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 11.05
Copyright ©2001-2016 Web Wiz Ltd.