|
DP RIFLES |
Post Reply 
|
| Author | |
paddyofurniture 
Senior Member 
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: DP RIFLESPosted: October 24 2025 at 1:51pm |
|
Are DP, Drill Purpose, Enfields always marked DP on the wood and/or just on the metal bits?
Think about buy some to use a a wood source now the NOS,New Old Stock,has gone away and is no longer available. Thanks |
|
 |
|
|
Canuck
Special Member 
Donating Member Joined: January 17 2012 Location: Cochrane, AB Status: Offline Points: 4021 |
Post Options
Thanks(0)
Quote Reply
Posted: October 24 2025 at 2:45pm |
|
Some wood parts (butt stocks and fore ends) were painted with colors denoting DP only. Especially, I have found, with the Indian No.1/MK3's.
|
|
|
Castles made of sand slip into the sea.....eventually
|
|
|
|
|
paddyofurniture
Senior Member
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
Post Options
Thanks(0)
Quote Reply
Posted: October 24 2025 at 3:59pm |
|
Sounds like DP will be good wood donors.
Thanks |
|
|
|
|
A square 10
Special Member
Donating Member Joined: December 12 2006 Location: MN , USA Status: Offline Points: 16998 |
Post Options
Thanks(0)
Quote Reply
Posted: October 24 2025 at 4:01pm |
|
a lot of folks have taken that route to replacement wood , you can refinish to your liking , its a good alternative
|
|
|
|
|
Bear43
Special Member
Donating Member Joined: August 11 2010 Location: Doland, SD Status: Offline Points: 3500 |
Post Options
Thanks(0)
Quote Reply
Posted: October 24 2025 at 7:10pm |
|
I've used DP wood many times in the past. I do recommend removing any of the DP marks on the wood just to avoid confusion for later.
|
|
|
|
|
paddyofurniture
Senior Member
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 5:23am |
|
What is the best way to remove the DP markings in the wood?
|
|
|
|
|
Bear43
Special Member
Donating Member Joined: August 11 2010 Location: Doland, SD Status: Offline Points: 3500 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 5:57am |
|
If they aren't deeply stamped you can steam them out. Otherwise you may have to be aggressive with sandpaper. Another option would be to line out the mark.
|
|
|
|
|
paddyofurniture
Senior Member
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 7:18am |
|
Thanks!
That works for me. |
|
|
|
|
Shamu
Admin Group
Logo Designer / Donating Member Joined: April 25 2007 Location: MD, USA. Status: Offline Points: 20510 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 10:41am |
|
I know some wood was "DP" stamped, but not how many or how common it was. I replaced my split lower hand-guard for "The Queen of the La Brea Tar-pits" with one I bought online, only to find a very faint "DP" stamp embossed into it. It didn't bother me as it was so faint & isn't any kind of pressure bearing component. Apart from the stamp is in excellent condition.
|
|
|
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)
|
|
|
|
|
paddyofurniture
Senior Member
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 10:54am |
|
Thanks
|
|
|
|
|
paddyofurniture
Senior Member
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 1:36pm |
|
is there any market for the metal DP bits?
|
|
|
|
|
A square 10
Special Member
Donating Member Joined: December 12 2006 Location: MN , USA Status: Offline Points: 16998 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 3:18pm |
|
sure as long as they are in condition that matches the buyers needs , i think you might find that a lot of parts suppliers have salvaged DP parts in their bins
|
|
|
|
|
paddyofurniture
Senior Member
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 3:25pm |
|
Good to know.
|
|
|
|
|
Doco Overboard
Senior Member
Joined: January 26 2020 Location: USA Status: Offline Points: 279 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 4:02pm |
Sometimes you can get away with a good bit, of she!!ac and fine dust from sanding like/similar wood that will color match. Mix it together to form a paste, slodge it on what ever you want to hide and then... Use wet dry paper like 400# to very deftly remove the excess with some Linseed oil as the carrier. Match up with some alcohol stain and rub it all out with some bee's wax. This where if something is struck deeper, it will actually help a tad bit. Couple toothpick drops and some sanding dust with she!!ac, it will dry in about an hour or less depending on the temperature. Use a backer for you paper, hard eraser, small wood block etc. and go light. Keep the paper wet with the oil. |
|
|
|
|
paddyofurniture
Senior Member
Joined: December 26 2011 Location: NC Status: Offline Points: 7942 |
Post Options
Thanks(0)
Quote Reply
Posted: October 25 2025 at 4:50pm |
|
Thanks!
|
|
|
|
|
Post Reply
|
|
| Tweet |
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
paddyofurniture wrote: