Another Ishapore |
Post Reply | Page 12> |
Author | |
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
Posted: October 15 2019 at 6:31pm |
just got this today . I hope I didn’t screw up.
|
|
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
|
more pics
|
|
A square 10
Special Member Donating Member Joined: December 12 2006 Location: MN , USA Status: Offline Points: 14452 |
Post Options
Thanks(0)
|
very nice 2A , it all looks to be correct and in good nick as well , should perform well for you , these are quite nice rifles - i occasionally miss mine when i see these posts , i think you did quite well , congrats
|
|
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
|
Thank you ,
I traded an AK I’ve had for years for this one. I am a bit puzzled however. The gun shop owner had it tagged as a 308 caliber but the wrist is clearly marked as 7.62. I also wonder why the model Mklll markings went? Scrubbed in Ishapore I assume.
|
|
Goosic
Senior Member Joined: September 12 2017 Location: Phoenix Arizona Status: Offline Points: 8792 |
Post Options
Thanks(0)
|
The 2A1 7.62mm rifle receiver was made with a stronger steel. Ishapore did not convert existing No1Mk111* rifles to 7.62. The .308 and 7.62x51 have one difference, and that is the shoulder area of the case. In the following photo,the bullet on the left is .308 and the bullet on the right is a 7.62x51. The .308 ammunition will chamber in the 7.62 rifle but not all NATO ammunition will chamber in new .308 rifles.
|
|
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
|
Based on your statement, I should go with the stamping info on the rifle. The shoulder of the 7.62 round does appear to be shorter and a slightly different angle. Interesting!!
|
|
Zed
Special Member Donating Member Joined: May 01 2012 Location: France Status: Offline Points: 5585 |
Post Options
Thanks(0)
|
Also consider that the velocity and pressure are different; with the NATO spec being slightly lower than .308 rounds. There are many versions of .308 with different bullet weights and loads for hunting etc. That's why it's better to stick with the NATO spec. If you reload; you can use the .308 components and load to NATO spec velocities to keep it safe. That's a very nice clean example. Please show us the range report when you find time. |
|
It's nice to be important, but it's more important to be nice!
|
|
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
|
You can count on my range report. I’m going to disassemble and safety check it out and put a few 7.62 bullets down range this weekend for sure.
|
|
Bear43
Special Member Donating Member Joined: August 11 2010 Location: Doland, SD Status: Offline Points: 3059 |
Post Options
Thanks(0)
|
You have a nice 2A now you just need a nice original 2A1 to go with it. The rear sights are different. Now that you have a couple just be careful. They breed like rabbits
|
|
Honkytonk
Senior Member Joined: December 30 2017 Location: Brandon Mb Status: Offline Points: 4770 |
Post Options
Thanks(0)
|
I blame this site. Before I joined I had one Sporter. Since then I've aquired a No5, another No4 Sporter, a L42A1clone, a No4 Mk2 (which I made into a Sniper clone), and a No1 MkIII. Shame on all of you!
|
|
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
|
This piece doesn’t appear to have any import marks either.
Not sure if that’s good or bad.
|
|
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
|
I’m afraid I may have stepped in it on this purchase. I’ve measured the barrel length from inside the muzzle to the face of the closed bolt. I’m getting 20”. I’m pretty sure it should be 25.5”. The lower stock also appears to have been shortened. Notice the distance from the rear of the nose cap to the barrel band. When I removed the wood I noticed a splice made to the lower hand-guard at the barrel band.
I still haven’t been to the range to shoot it. The barrel crown doesn’t look bad. Please! Someone tell me that Ishapore built a carbine.
|
|
Goosic
Senior Member Joined: September 12 2017 Location: Phoenix Arizona Status: Offline Points: 8792 |
Post Options
Thanks(0)
|
Nope!
Gibbs Rifle Company shortened some of them to make a 7.62 Jungle Carbine and a Tanker version. Yours could be one of them. Alot of Enfield rifles have a tendency to become something they were not from people who have no idea what they have in its original form and think they can improve on an already perfect rifle. Take it for what it is now and enjoy it...
|
|
A square 10
Special Member Donating Member Joined: December 12 2006 Location: MN , USA Status: Offline Points: 14452 |
Post Options
Thanks(0)
|
agreed - use 762x51 in it , it was a longer one originally but a fine looking rifle and as stated enjoy it as is , you will not be disappointed in it i think ,
|
|
Frameman 1
Senior Member Joined: July 30 2019 Location: SW Ohio Status: Offline Points: 382 |
Post Options
Thanks(0)
|
I’m going to take your advice. I still need to do a bit of work to the wood in letting. The wood behind the steel pillar for the front trigger guard screw is blown out and the recoil blocks at the trigger action is beaten a little. A little Acraglas will fix this problem.
The history of this rifle just got more interesting.😎
|
|
Shamu
Admin Group Logo Designer / Donating Member Joined: April 25 2007 Location: MD, USA. Status: Offline Points: 17603 |
Post Options
Thanks(0)
|
I think you got a tanker conversion. In their own way they're neat. Do check the splice you found, some forend tips have been known to launch downrange on firing due to gluing oily wood together.
|
|
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |