Enfield-Rifles.com Homepage
Forum Home Forum Home > Reloading > Reloading .303 British
  New Posts New Posts RSS Feed - Paper Patching for the 303
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

Paper Patching for the 303

 Post Reply Post Reply
Author
Message
303Guy View Drop Down
Senior Member
Senior Member


Joined: July 10 2012
Location: Auckland
Status: Offline
Points: 489
Post Options Post Options   Thanks (0) Thanks(0)   Quote 303Guy Quote  Post ReplyReply Direct Link To This Post Topic: Paper Patching for the 303
    Posted: December 30 2013 at 10:37am
Just wondering if anyone is interested in this art.  I've successfully paper patched for two rifles, both with oversize bores.  One of those had a layer of rust scale coating the entire bore and the barrel was bent near the end by someone hammering the site ring onto a cut down muzzle!  I cut off more of the barrel and then straightened it - a bit tricky as the bore had zero shine and that layer of rust scale but I did it.  I then fire-lapped the bore which removed the rust and dulled the pitting edges and believe it or not there was a semblance of rifling!  By now the bore was somewhat oversize to say the least.

Anyway, I got this thing to shoot with paper patched bullets and that is my whole point - rust damaged and worn bores can be made to shoot pretty well by paper patching cast bullets.  The other rifle - a cavalry carbine barrelled 1896 MLE - must have seen many cordite MkVII rounds but it does still have a shadow of rifling in its now .314/.318 (or whatever) bore.  This one shot great from the get go with paper patched bullets.

My mint bore, No4 barrelled 1902 MLE, not so much.  The throat is just too fresh to use the methods that worked in the worn bores.



this is how I got the rusted barrel gun (a 1904 ShLE I***).  I've driven 194 gr paper patched bullets to 2000 fps with moderate pressure from it's 15½ inch barrel.  Accuracy was not so good at that velocity.  But with milder loads it's not too bad and with 148 gr PPCB's it's pretty accurate.
303Guy
Back to Top
Sponsored Links


Back to Top
Canuck View Drop Down
Special Member
Special Member
Avatar
Donating Member

Joined: January 17 2012
Location: Agassiz BC
Status: Offline
Points: 2503
Post Options Post Options   Thanks (0) Thanks(0)   Quote Canuck Quote  Post ReplyReply Direct Link To This Post Posted: December 30 2013 at 11:17am
Goes to show there can still be lots of life left in the old guns, you just need to do the right things. Good for you, 303Guy, good going.
Castles made of sand slip into the sea.....eventually
Back to Top
303Guy View Drop Down
Senior Member
Senior Member


Joined: July 10 2012
Location: Auckland
Status: Offline
Points: 489
Post Options Post Options   Thanks (0) Thanks(0)   Quote 303Guy Quote  Post ReplyReply Direct Link To This Post Posted: December 31 2013 at 11:31am
Thanks.  Here is a loaded round.

A patched bullet.

303Guy
Back to Top
303Guy View Drop Down
Senior Member
Senior Member


Joined: July 10 2012
Location: Auckland
Status: Offline
Points: 489
Post Options Post Options   Thanks (0) Thanks(0)   Quote 303Guy Quote  Post ReplyReply Direct Link To This Post Posted: December 31 2013 at 11:37am
I should mention that velocities can equal jacketed bullet velocities and that with less powder and lower pressure because the paper patch has a lower friction/resistance than metal jackets.

This is a 256 gr plain cast bullet fired through that bore in my opening post.  It was smeared with a metal polishing compound before firing and was real slow which is why it could be captured in such condition.
303Guy
Back to Top
Flenzer View Drop Down
Newbie
Newbie
Avatar

Joined: June 07 2019
Location: Australia
Status: Offline
Points: 1
Post Options Post Options   Thanks (0) Thanks(0)   Quote Flenzer Quote  Post ReplyReply Direct Link To This Post Posted: June 07 2019 at 6:05pm
Greetings 303Guy
Are you still out there 6 years on ?
Back to Top
pisco View Drop Down
Groupie
Groupie
Avatar

Joined: November 21 2018
Location: australia
Status: Offline
Points: 27
Post Options Post Options   Thanks (0) Thanks(0)   Quote pisco Quote  Post ReplyReply Direct Link To This Post Posted: June 22 2019 at 11:35pm
hi if you can get a bigger mould try rolling the loaded bullets in baby it will stick to the lube then fire lap the barrel have done a bit of it with 303s 
Back to Top
A square 10 View Drop Down
Special Member
Special Member

Donating Member

Joined: December 12 2006
Location: MN , USA
Status: Offline
Points: 9349
Post Options Post Options   Thanks (0) Thanks(0)   Quote A square 10 Quote  Post ReplyReply Direct Link To This Post Posted: 9 hours 49 minutes ago at 8:23pm
i did this a while back and felt it was too much trouble for the results but i would never dissuade any purist from making the effort , im sure someone will benefit far beyond my abilities 
Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.01
Copyright ©2001-2018 Web Wiz Ltd.