Print Page | Close Window

Santa Fe Carbine rear sight help!

Printed From: Enfield-Rifles.com
Category: Enfields
Forum Name: After Market Enfields
Forum Description: What have you done to that Enfield??
URL: http://www.enfield-rifles.com/forum_posts.asp?TID=13287
Printed Date: March 26 2026 at 2:51pm
Software Version: Web Wiz Forums 12.07 - https://www.webwizforums.com


Topic: Santa Fe Carbine rear sight help!
Posted By: Redman
Subject: Santa Fe Carbine rear sight help!
Date Posted: March 28 2024 at 5:03pm
Ok, stop laughing! it only cost a couple hundred bucks. But... Im sure someone has ran into the sight issue on these things!when i got it, it was just flippin and a floppin. Took the bolt out cause someone had the head one turn loose and when i did the sight hit the floor and now all i have is that and a brass washer i stole from a safety assembly. No screw. (unique and hard to find! screw) it has another small hole in front of the one for the attaching screw and not sure what that is for?  I know that you guys know some Guinness that has a cure for this crap ass rear sight! Actually seems like a cool little gun and pretty sharp looking for what it is. They just cut a piece out the bridge and stuck a L shape chunk of steel with 2 holes drilled in there!! So it was a 1940 dated MKlll* and believe is an SSA, so that sucks. HELP ME, With a solid sight, should still be a fun shooter, has a great bore, RED 



Replies:
Posted By: shiloh
Date Posted: March 29 2024 at 2:34am
I think a single screw and a stout wave washer is about all there was. the washer kept tension on the sight and also allowed to flip between apertures.
That other small hole is part of the manufacturing of the charger bridge.


Posted By: Redman
Date Posted: March 29 2024 at 6:13am
yea, i saw the wave washer and lost that! dont think it even had a screw with it, know anyone or any where to find the correct screw? not a hardware store thing. Thanks


Posted By: shiloh
Date Posted: March 29 2024 at 6:38am
Shouldn`t be hard to find a screw, it`l probably be either an 8-32 or 8-40, maybe a 10-32. These were converted in the States not England.
Hardware shops or a good gunsmith will have these sizes.


Posted By: A square 10
Date Posted: March 29 2024 at 6:58am
as you probably know these were made up by those at santa fe , they cut the charger bridge and mounted the rear sight from something else to the receiver there , so - not standard parts , your best bet will be a good hardware store and some trial and error fitting up ,there are no original standard bits for these , 


Posted By: BrianBDL
Date Posted: April 01 2024 at 10:38am
The screw/pin that holds the Santa Fe rear sight in place is an SMLE sear screw. The sight itself is a No.4Mk.II that's been ground down to fit the slot. 


Posted By: Goosic
Date Posted: April 01 2024 at 1:32pm
Welcome aboard Brian!!


Posted By: Shamu
Date Posted: April 01 2024 at 4:01pm
SMLE sear screw?
I thought the SMLE was a different thread form?
Can you clarify a bit.

Oh, Welcome aboard! Tongue


-------------
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)


Posted By: Redman
Date Posted: April 01 2024 at 7:57pm
The screw problem has been fixed and I cupped a thin brass washer to tighten it up. But I dont agree with it being a sear screw. and they should have just used a mk 2 sight but they did not, mine and the others i have seen are the same aftermarket looking steel dual aperture sight. The one i have someone cut one right through the center of the hole making it a make shift notch style? Thing is there is no kind of stop for the 2 positions so just kinda making it tight as possible. Was just hoping someone would have brainstormed a good positive holding and good lookin sight for these? DO they make a nice Redfield or Lyman that will work? since i dont have to worry about originality, could only help! Thanks, RED  


Posted By: A square 10
Date Posted: April 01 2024 at 9:22pm
if anyone would be a definitive responder to this it would be Brian , i would trust what he said and look for the bits he mentioned - most likely he can provide them , he was instrumental in getting me some things over the years , 


Posted By: Redman
Date Posted: April 02 2024 at 6:30am
Ok, after looking, like i should have done before i spoke! Brian, I believe is right about the screw? sure looks like the correct one? screw I'm using now i found is a sear screw from an old marlin rifle. Just hate to spend 10 bucks for it! MK2 sight would look a lot better but not sure about sight alignment (position) will work, seeing that the aperture hole would be setting lower.  believe that was the reason i haven't seen them used? But heck! I'm probably wrong about that too! RED


Posted By: shiloh
Date Posted: April 02 2024 at 6:45am
You can always put an aperture sight on it. Lots out there, some cost more than others.



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.07 - https://www.webwizforums.com
Copyright ©2001-2024 Web Wiz Ltd. - https://www.webwiz.net