Print Page | Close Window

Webley .45ACP Adapter Plates

Printed From: Enfield-Rifles.com
Category: Enfields
Forum Name: Enfield Pistols
Forum Description: Another great Enfield!
URL: http://www.enfield-rifles.com/forum_posts.asp?TID=14281
Printed Date: March 26 2026 at 2:51pm
Software Version: Web Wiz Forums 12.07 - https://www.webwizforums.com


Topic: Webley .45ACP Adapter Plates
Posted By: mrbieler
Subject: Webley .45ACP Adapter Plates
Date Posted: November 29 2025 at 5:36pm
Have this Webley MkII that, as so many were, converted to .45ACP by shaving the cylinder.  I know there were adapter plates available so I could shoot .455 in it but I haven't been able to track one down.  Any leads?




Replies:
Posted By: Shamu
Date Posted: November 30 2025 at 11:04am
Try looking for "Full Moon Clips" for .45 in a .455 webly

-------------
Don't shoot till you see the whites of their thighs. (Unofficial motto of the Royal Air Force)


Posted By: mrbieler
Date Posted: November 30 2025 at 11:22am
Have plenty of full and 1/2 moon clips for my Colt 1917, S&W 1917, and S&W M-22 Thunder Ranch.  

I know I can get soft cowboy action .45 ACP lead loads in and around 13000psi which should be safe to shoot in the Webley, but it's a smaller bullet rattling down the barrel.  Was looking for the conversion plates I recall seeing that would bring the cylinder length back up to accommodate .455 cartridges.

I do need to get off the fence and just start reloading...


Posted By: A square 10
Date Posted: November 30 2025 at 3:50pm
please note that preasure issue the mkII was a black powder revolver and not rated for the 45acp or the later smokeless 455 , you would need to get to the mkV before you could trust smokeless in these and even then id download to the cowboy loads [and i do in the few i have left of my cllection these days 




Posted By: mrbieler
Date Posted: December 01 2025 at 10:55am
The MkII were nitro proofed and marked as such but I agree on the low power loads.  If I can pick up or reload ACP in the 600~650FPS range with a decent lead bullet, I should be under 13000PSI which is what they were proofed to.  

3.5grains of Trail Boss with a LRN would come in below 12000PSI.  Pretty common for the Cowboy Shooters using old Schofields, etc.


Posted By: britrifles
Date Posted: December 02 2025 at 8:55am
I loaded .451 copper plated (not jacketed) lead bullets seated into the .455 Webley Mk I and Mk II cases with good accuracy in my Mk V.  The plating is thin and the bullet seems to upset into the grooves.  I'll dig out my notes tonight and find the recipe.  I know I tried Unique, Bullseye and I think I also tried Trail Boss. 

Or, you could use cast lead bullets sized to 0.454 - 0.455 loaded into the .45 ACP case, using minimum powder charge.  Agree on the above, I would not shoot .45 ACP factory ammo in these revolvers.  

 


Posted By: bubba ho tep
Date Posted: December 02 2025 at 4:39pm
I use whatever the RCBS mold drop out , lube grooves , load and have no issues. 


Posted By: A square 10
Date Posted: December 02 2025 at 6:22pm
mrB , thats exactly where i would go but still be careful , actually id not go smokeless before the mkV as thats when they transitioned to smokeless , just me being oon the safe side , 

i do load to those levels for my mkV as its the one ive kept from my collection , 


Posted By: britrifles
Date Posted: December 03 2025 at 3:25am
I read somewhere that the cylinder diameter was increased (increasing the chamber walls thickness) for the Mk V to use smokeless loads?  



Posted By: A square 10
Date Posted: December 04 2025 at 4:37pm
that was my research as well , pre mkV is BPonly 


Posted By: mrbieler
Date Posted: December 05 2025 at 11:02am
I believe the first nitro proofed Webley’s started in 1896.  



Print Page | Close Window

Forum Software by Web Wiz Forums® version 12.07 - https://www.webwizforums.com
Copyright ©2001-2024 Web Wiz Ltd. - https://www.webwiz.net